A brief explanation about dongle:
Dongle mostly acts like Decoder which by receiving shared code from its satellite and signal receiving from usual satellites, decrypt the Encrypt channel and you see the channels opened. Your receiver will not change to anything and there is no hack.
Personal point of views:
Try to use a set which supports internet sharing, like DVB cards for computer and those receivers that supports Gbox or in the best way: those Linux receives that supports CCcam server and all sharing protocols.
Internet sharing opens both more channels (Hot Bird, Nile sat, and Badr etc) and has long time stability (if you have a DVB card you could use it for a life time because Gbox and CCcam will never extinct.
Those who have limited internet volume are concerned about using this limited by internet sharing but it is good to know that if you use CCcam server 24 hours in every day of a week ( it’s a voluminous immolator in data transporting) you will use less than 100 mega bit per month.
How does Server for Cardsharing Benefits You?
As you flip through channels, some of them are obviously locked, aka they are encrypted because you didn’t pay the satellite provider to make them available for your viewing pleasure. Now, your standard satellite receiver will show only those channels that you paid for, there’s no way it can decrypt (unlock) channels at no cost since it wasn’t designed to support cardsharing or run CCcam protocol software. But, there are other models of satellite receivers which are cardshare-capable and a lot of online stores sell them.
One of the most popular choices is the Linux-based satellite receiver called the Dreambox. Once you get your hands on one of those bad boys, hook it up to the PC, insert your satellite smart card in it, download and install the CCcam computer software, configure it and run it – after all that (if done correctly) you will be able to establish a connection with the CCcam server cardsharing server of your choice.
Your receiver will be communicating with the server which in turn will be sending you the decrypted channel codes, meaning that you will gain a full access to the satellite TV channels which were previously unavailable. The cardsharing server shares the decrypted information obtained through yours or anybody else’s satellite subscription card with other users who are connected to it. The amount of obtainable channels depends on the area you live in, the direction your satellite dish is pointing at and its size.
How to Find the Best Card Sharing Server
After you google the words “cardsharing server” you will find tons of CCcam servers available for cardsharing. To find the best CCcam server you will have to spend a great deal of time researching to pick the one which will better suit your needs. But to narrow it down, all you need to do is look out for those servers which offer the best choice of satellite TV packages and are known for their steady and reliable connection so you could enjoy watching your favorite programming without any interruptions.
I am using TV Headened as the TV backend for Openelec/XBMC.
TVHEADEND works pretty good, no problem with the FTA channels, but PAYTV channels couldn be descrambiled.
I have a CCCAM C-Line for a CCCAM Server.
I know I habe to use OSCAM for it.
My oscam.server file looks like that:
label = sky de,orf,hd+,srg
enable = 1
protocol = cccam
device = cccam server
user = USER
password = PASS
caid = 1702,1830,0D05,0500,0648
ident = 1702:000000;1830:000000,003411;0D05:000004,000010;0500:023800;0648:000000
cccversion = 2.3.0
cccmaxhops = 1
ccckeepalive = 1
audisabled = 1
How do I have to setup my oscam.conf and how do I habe to configure TVHEADEND, that I can descramble the non FTA channels ?
Thanks for your answer.
Yeah… I should have mentioned before that I wouldn’t recommend anybody to rely on the correctness of the above .
These config files are the results of hours of browsing and reading.
The linked tutorial is useful for compiling (kind of, because RPi is ARM platform) but when it comes to the configuration ofCCCam server I’m lost
because I want to use it as a client only, means I have no reader attached but a C-Line I want to use.
Hostname: use the IP address of your cardserver. Either full IP, or if it is on the same machine, try full ip first, or 127.0.0.1 later.
The cardserver is running on 192.168.178.10, port 55555.
So instead of defining localhost in TVH I need to put this host?
Port: default is 15050, but you can also define one in ther webif section ( see the link to an example posted before).
I also see something like 55555 in your reader.config files, dont know what this is ( where did you get this file from???) but if either 15050 or a custm define one ( 15080 in the example ), maybe try that one.
You mean 15050 is the standard port for OSCam or TVHeadend? According to my “oscam.conf” (WebIf section, httpport = 8888) do I need to put this port 8888 in TVH?
Port 55555 is the port I manually configured my already running CCCam Server to listen on for incoming connections.
This part of the config I assume to work fine since I can see in the OSCam WebIf that the connection to the Cardserver has been established.
Last important question: Do I need to enter anything in “DES Key” ?
I’ll use your instructions and give it a try once I’m back home. Thanks!
Possible CCCAM PLUGINS.dll Error Messages
The module “CCCAM PLUGINS.dll” was loaded but the entry-point DllRegisterServer was not found. Make sure that “CCCAM PLUGINS.dll” is a valid DLL or OCX file and then try again.
Windows could not start because CCCAM PLUGINS.dll file is missing or corrupt.
Runtime Error! Program [path]\CCCAM server PLUGINS.dll. An application has made an attempt to load the C runtime library incorrectly. Please contact the application’s support team for more information.
[path]\CCCAM PLUGINS.dll is either not designed to run on Windows or it contains an error. Try installing the program again using the original installation media.
Error loading [path]\CCCAM PLUGINS.dll. The specified module could not be found.
This application has failed to start because CCCAM PLUGINS.dll was not found.
Can’t find CCCAM PLUGINS.dll
Information about CCCAM PLUGINS.dll File
Filename: CCCAM server PLUGINS.dll (Free Scan)
File Description : STARTIMES
Latest Known Version: 0, 2, 5, 0
Product Name : FLYCCCAM
File type : dll file
OS Infected: Windows NT/2000/2003/XP/Vista/2008/7/8
Security Level(0-5): 5
Recommended: Download CCCAM PLUGINS.dll Error Free Scan Tool
This CCCAM PLUGINS.dll file stores important information that how the program or a Windows service needs to run. As a result, it will pop up an error message when this file is corrupt or damaged. In such circumstance, you may have a problem running the program or using the computer properly.
Most of the time, you will get an error message when there is a computer error. That error message may give you any hint on what may be wrong. Knowing the root of the problem is half the battle won when it comes to fixing the error.
Usually, CCCAM server PLUGINS.dll error may be caused by:
The registry key of CCCAM PLUGINS.dll is invalid or damaged.
Computer malware has injected malicious code and modified CCCAM PLUGINS.dll file.
The CCCAM PLUGINS.dll file was uninstalled by other software.
The CCCAM PLUGINS.dll file was intentionally or mistakenly deleted by other software.
The required version of CCCAM PLUGINS.dll file is overwritten by other software.
There is a hardware failure, such as a bad hard disk.
How to Fix CCCAM PLUGINS.dll Error?
Attention: It’s not advisable to download CCCAM PLUGINS.dll file from those “dll download” websites. The file from those websites are not verified by the official CCCAM PLUGINS.dll developer and may be bundled with computer malware or other unwanted things. In case you really need a copy of CCCAM PLUGINS.dll file, it’s necessary for you to get it directly from its official resource. Now you can use the following solutions to fix CCCAM server PLUGINS.dll error:
۱٫ Recover CCCAM PLUGINS.dll file from Recycle Bin
In case you or your family mistakenly deleted this file, you can restore it from the Recycle Bin. But if you have already emptied your Recycle Bin, you can use a free data recovery software to recover CCCAM PLUGINS.dllfile. This solution works only if this file worked properly before you deleted it.
۲٫ Restart the computer
When you receive CCCAM PLUGINS.dll error message, you can try to restart your machine to see if this error could be a glitch. If you can’t restart it normally, you can force restart it.
۳٫ Fix corrupt or invalid registry entries of CCCAM PLUGINS.dll file
The registry is the place where most computer errors like CCCAM PLUGINS.dll error come from. When a software was installed or uninstalled incorrectly, sometimes there will be some invalid or corrupt registry entries of some software files like CCCAM server PLUGINS.dll are left in the registry. That’s why it’s necessary to regularly clean those invalid and corrupt registry entries and keep the registry compact so that such errors can be reduced and your computer performance can be improved.
Download AutoCCCAM PLUGINS.dllErrors Fix Tool
Attention: The system registry stores all information that all software and hardware require to run. So it’s not suggested that you clean the system registry manually. You should know that a slight mistake may make your software unpredictable or even crash your system.
۴٫ Run a disk defragmentation
When a software is installed, updated and removed, there will be fragments left all over your hard disk, which may lead to computer errors like CCCAM PLUGINS.dll error. A disk defragmentation can rearrange the data on your hard disk and make them together in one stream so that computer error could be reduced and your PC can be faster.
۵٫ Repair your Windows Operating System
Rather than wiping out your hard disk and reinstalling your system, you can perform a startup repair to repair your corrupt Windows system files that may be associated to CCCAM PLUGINS.dll file. By doing so, you don’t necessarily lose your software, personal information and settings.
۶٫ Use Windows System Restore to undo recent changes in the system
System Restore is a useful recovery tool in Windows that enables you to undo changes made to your system and software. But this works only if you have created a restore point when everything worked fine. If you restore your system to the earlier point, you will lose the software and data you got after this restore point.
AS we all know there are so many companies providing services in communication and tv satellite channels and they work on showing these satellite programs. Among all these companies most try to provide free service for customer on different tv channels. They focus on advertisement, financial sponsoring or government support to come over their money problems they may face.
But you also have noticed that there are some companies and firms which provide their services by asking their users to pay for amount of money as a charge of receiving the best service ever. These programs provided by these companies have less or in some cases no advertisement, so there would be enough time for better and more interesting programs. Live matches, soccer games and more options are available on these services.
These channels are only working with special cards or decoder devices provided by the company.
Here in CCCAM server, a card from a coded satellite package can be used as a shared card instead of being useful for just one person. Since these packages are almost expensive, these cards must be used as a shared one which works while all the codes are given to the users through the internet.
In this model, server buys the package card and in case of using special software and hardware it can share the cart for other several servers or users. So the user is able to have many packages with lots of channels instead of having just one.
In recent years these companies which has been working as channel providers faced a great decrease in number of users since the users have been more interested in having many channels instead of one.
CCCAM servers provide great opportunity for their users in order to watch tons of channels across countries. It is obvious that user has got a great range of choosing options and is able to follow whatever he is looking for.
There are so many other items except CCCAM server such as CAM3, MGCAMd, and OSCAM and …. Which unfortunately face great problem according to receivers setting.
Here in CCCAM far apart from the great hardware used in servers, the server configuration and setting has been always under control since we have heard of bad user experience in case of having great hardware but not well setting on the servers.
۱: Go into the main menu
۲: Select Network, enable your network and set the IP address to DHCP. Go back to network.
۳: Select “CCcam Client Setup” If you can not see CCcam server setup in the menu jump to number 9
۴: If you have a cccam.cfg on your usb, we provide the CCcam.cfg file, ask for the full configured file from us to get all of our channels. Copy the CCcam.cfg file into the root folder from your USB stick. Do not copy the file in a specific folder.Select ‘Update files by usb’ if not, jump to number 10
۵: On new window, highlight ‘CCcam.cfg’, press green button on remote (ADD). This will place a tick by it, the press yellow button on remote (READ)
۶: Once finished, select ‘Manage Config Files’ and on new window select cccam.cfg again
۷: A new page comes up with your cline on it, press green button on remote to make it active (tick should appear by it) Exit out of all menus to tv and select a pay channel.. it should clear, if not go back into menu, select Network, then ‘Network Setup’, and turn DHCP ‘off’ by using arrow keys and then hitting apply.
۸: if channel still doesnt clear, reboot box and router by unplugging both from power and plugging back in (router first)
۹: if you cant see this option go to network and press 0000 or 6666 or 8888 or 2778 this should bring up hiden menu.
۱۰: for those who didnt create a cccam server on their usb, you can add it manually..
a] instead of update by usb on ccccam client setup, go directly to Manage Config Files and select CCcam.cfg from new window
b] Press Blue button on remote
c] your cline will look something like this>>> C: example.cline.org 12000 user pass
d] ON add cline window, leave Protocol as CCcam
e] Host: here you would enter example.cline.org portion of your cline using remote number buttons like you was sending a text
f] Port: here you put 12000
g] User, write ‘user’ here
f: Password, write ‘pass’ here
g] Press ok and go up to instruction number 7 OF CLINE SETUP
What is Ping cccam server?
Ping is a command under DUS operating system with which number of sent and received packets and duration of this transportation per ms could be specified. For better understanding I will explain in this way:
In order to open a $ channel you have to send the code request send to the server (CCcam server) through internet and after receiving the code, it will be transported from internet to your receiver. This sweep time in code receiving is called Ping. The shorter the time is the faster the channels will be opened.
The way Ping is measured is by is easy:
From start menu go to RUN
Copy CMD from RUN menu
DUS black page will be opened instantly
Write this phrase in front of blinker _
Ping 126.96.36.199 -t
In this case you can see your internet ping per ms; the best range for Pig in order to use CCcam server is under 200ms.
Important: this phrase “Request time out” means that sending or receiving data is failed. For every time out we have 20s disconnection and freeze.
Ping number with no time out is essential for having a CCcam server with no failure. In case of any default contact your internet service provider and consult them.